Iphone Won’t Connect To 2.4 Ghz Wifi

by -133 views
RobotPoweredHome is reader-supported. When y'all purchase through links on my blog, I may earn an affiliate commission. As an Amazon Associate, I earn from qualifying purchases.

I have fix my network to automatically connect my smart devices around the home and devices that are far abroad to the ii.four GHz band of my dual-ring router.

Devices that are closer and usually apply more data like my gaming panel, Tv, and computer, connect to the v GHz.

The same is the case for my phone and laptop which automatically change between 2.4 GHz and five GHz bands depending on the distance from the router as I move around the dwelling.

Just equally of belatedly, my connectedness with the 2.four GHz band has been pretty patchy, and most of the time, my devices won’t even connect to the Wi-Fi.

Without Wi-Fi’s convenience, piece of work would be difficult to consummate on time, and so I went online to find out why this was happening.

I hoped to find something that would fix this issue once and for all and bring my router back to seamlessly switching between two.4 and five GHz Wi-Fi.

Later a few hours of enquiry that comprised reading forum posts and router documentation, I was ready with a few fixes that I knew could piece of work.

I tried them on my router and my devices and managed to get it to work in just a few minutes.

This article compiles everything I found and should aid you connect to the 2.4 GHz network once more.

If your device can’t connect to your 2.4 GHz Wi-Fi band, check your device settings and make sure it’due south set to connect to the ii.4 GHz ring. You tin as well update your router and your device and restart or reset the router.

Find out later in this article how you tin can update your router’south firmware and why keeping your device updated and on the latest software is important.

Check Device Settings


Some devices have a setting that, when turned on, won’t connect to ii.4 GHz Wi-Fi networks.

The feature might have been intended to maximize the device’south performance on Wi-Fi by using but v GHz, but it doesn’t allow y’all connect to the slower ii.4 GHz band.

Bank check your device settings to see if your device has the same or similar setting, and turn it off for the moment.

Endeavor connecting the device to the 2.iv GHz access point at present and run into if you can complete the connection.

Update Your Device

As your device’due south software is existence worked on, the developers will launch updates and patches for it every once in a while.

These patches iron out bugs and other issues that might have affected the device’southward performance.

Bugs cause devices to not connect to Wi-Fi networks and the i that yous may accept stopped your device from specifically connecting to the 2.iv GHz band.

This is why it’due south pretty important to keep your devices updated and on the latest version of patches and issues fixes.

Bank check for updates to your devices and install them every bit before long as possible.

After your device is updated, try connecting the device to the ii.4 GHz ring over again.

Update Router Firmware


The same logic applies to your router, but getting it updated is a bit different from updating your other devices.

Routers usually update their firmware instead of software because routers use software that better interfaces with its hardware.

To update your router’southward firmware:

  1. Go to your router’southward support website.
  2. Check for firmware updates to your router model and download information technology to your reckoner.
  3. Open a new browser tab.
  4. Type 192.168.ane.1 in the address bar and hit Enter.
  5. Log in to your router. Y’all tin can find the default login details on a sticker underneath the router.
  6. Go to the Administration section. If it isn’t present, you can refer to your router’s manual for the exact section that you’ll demand to go.
  7. Upload the file y’all just downloaded to the router.
  8. Kickoff the firmware update.
  9. The router will restart after the firmware update completes.

Try connecting your devices to the 2.iv GHz access point again to see if the update worked.

Restart Your Router


If a router firmware update didn’t work, and neither did a device update, you tin endeavour restarting your router to see if that helps.

Restarts human activity as a soft reset and have been seen to ready quite a few bugs with many routers.

The all-time way to do this would be a power bike, so follow the steps beneath to exercise and then:

  1. Plow the router off.
  2. Unplug it from the wall.
  3. Plug it back in only after waiting at to the lowest degree one minute.
  4. Turn the router dorsum on.

Later the router turns on, connect the device to the 2.4 GHz access point.

Yous tin endeavour this a couple more than times if information technology doesn’t piece of work the first time.

Reset Your Router


If a restart doesn’t work, the next logical step to take is to factory reset the router.

This will wipe all settings, including your custom Wi-Fi name, QoS settings, and restore the Wi-Fi password to defaults.

But do this if you’re prepared to ready everything upward again from scratch.

To reset your router:

  1. Find the button labeled ‘Reset’ on the back of the router. Information technology should be recessed and look like a pinhole.
  2. Go a paperclip or something non-metallic and pointy to printing the button.
  3. Press and hold the push button for at least thirty seconds with the tool.
  4. The router will restart, and when it comes dorsum on, the process has been completed.

Endeavor connecting a device to the 2.4 GHz band of the router after setting it upward to see if the reset worked.

Contact Support


If none of these troubleshooting steps works out for yous, please contact your router’s technical support.

For routers that you’ve leased from your Internet access provider, it’s better to contact your Internet service provider instead.

They guide y’all through additional steps and might ask you to transport it to them if they can’t set it over the phone.

Last Thoughts

two.4 GHz is almost used exclusively for the range advantage that information technology has over five GHz, and because of costs, most smart home devices also apply merely ii.4 GHz Wi-Fi.

If your dual-band router has reliability issues with 2.iv GHz, consider getting a single band ii.4 GHz router, and utilize the dual-band router for 5 GHz Wi-Fi.

I would recommend the ASUS N300 single-band router if you lot want a skilful ii.four GHz router.

Interference won’t be much of an issue if yous place your router strategically.

You May Also Savor Reading

  • Tin can’t Connect To 5GHz Wi-Fi: How To Fix In Seconds
  • Why is My Wi-Fi Signal Weak Suddenly
  • Xfinity Wi-Fi Connected Only No Internet Admission: How To Fix
  • Ethernet Slower than Wi-Fi: How to Fix in Seconds

Oftentimes Asked Questions

How do I modify my Wi-Fi frequency?

You need to accept a dual-ring router to modify your Wi-Fi frequency.

These dual-ring routers usually show as 2 access points on devices that support both Wi-Fi bands.

Connect to the access bespeak, which has 5 in the proper noun for that ring or ii.4 for the two.4 GHz ring.

Can I force my telephone to utilise 2.4 GHz?

To force your phone to use 2.4 GHz, connect to the 2.4 GHz access bespeak and make the phone forget the v GHz AP.

Tap and hold the 5 GHz access point and forget the network.

Does iPhone utilize 2.4 GHz or 5GHz?

All iPhones from the 12 and newer have support for both 2.iv and 5 GHz Wi-Fi.

Older models don’t have back up because they don’t accept the required hardware.

Should I use dissimilar SSIDs for 2.4 and 5Ghz?

Your router already uses a slightly unlike SSID for both bands, but to make your life easier and identify the bands, you tin can change the SSID to annihilation y’all wish.

Source: https://robotpoweredhome.com/cant-connect-to-2-4-ghz-wifi/